panasonic receiver overload error Alkol West Virginia

Address 194 Nancy Dolin Rd, Julian, WV 25529
Phone (304) 307-4492
Website Link https://www.facebook.com/M4ComputerRepair
Hours

panasonic receiver overload error Alkol, West Virginia

Ultra Hi-End HT Gear ($20,000+) D-cinema Equipment and Theaters High Dynamic Range (HDR) & Wide Color Gamut (WCG) Screens As for the ohm the speakers are 4 and the receiver can handle that from what i understand.... In my case, it was IC602 with the weird voltages there. Fan motor failure.

We are unable to respond to questions submitted here. However, the price difference is substantial, so I will give another update when I manage to buy the grounded, shielded speakers' wires. Tesla, Jul 21, 2010 #13 keine Joined: Jul 15, 2010 Messages: 7 Likes Received: 0 Thanks for the reply Tesla, I really appreciate it. Man it scares the crap out of me.

Does the receiver have plenty of breathing room? While it played for hours with the cover off (with the 2 JBL towers and 1 center ... Not burning, as I could easily keep my hand on them. Passive cooling (fan off) is fine most of the time ...

Following information available from several forums, i opened the unit and replaced a 1.25A fuse which had blown.( i do have an electronics background and am happy to attempt such repairs) Mine is still working fine. I took it into a local Panasonic repair shop and they fixed it. It that relay in any way replaceable?DeleteReplyStephen J OäkesSeptember 28, 2015 at 10:57 PMHi everybody.

LCD Flat Panel Displays LCD Flat Panel Great Found Deals! Tesla, Jul 16, 2010 #11 keine Joined: Jul 15, 2010 Messages: 7 Likes Received: 0 44 minutes into a DTS DVD film using 5.1, BOOM! He too has the problem with one MOSFET. Too bad we can't adjust the "on" value.

The pins I soldered are for the power amplifier modules and they look similar, if not identical, to the grey modules attached to the aluminum heat sink with fins. That is really handy of a broken receiver! for testing only) and no more OVERLOAD condition ... The receiver goes to error without wires connected, so it's logical that the speaker's wires have nothing to do with the problem.

I will have a look at these soon. I've seen this more times than I can count on fingers and toes. Then finally locked onto pins 2 and 3 loose (again not visible, but it is at a microscopic level where small amount of temperature and/or pressure would make or break the Remove one speaker.

This fixes the problem, but it really annoying to plug in the wallwart AND turn on the amp everytime I want to do something. It's returned sporadically again. I do not understand how the heatsink can cope even as lower power levels without some sort of active cooling. Using a fine-tip soldering iron, tweezers and a magnifying glass I was able to reattach the components.

Oh well, for a 6.1 receiver, was pretty hard to beat! I will advise of my success or failure in due course.ReplyDeleteMartin QApril 17, 2014 at 7:43 PMExcellent work and thanks for the update. It took several days of reading, testing, wondering and poking through and happy to say I fixed it and understood, I think, the exact causes for my unit as well as All is fine.

DC offset. More fellow SA-HE200 owners and their repair success stories are here:http://www.electronicspoint.com/pana...x-t220907.html Living Room Home-Theater: Epson 8350 Projector (1080p @ 96") / Panasonic 850u 46" 1080p Plasma TV Onkyo TX-sr607 AVR (7.2ch steve45 is offline Quote post #7 of 18 Old 01-22-2010, 09:48 PM - Thread Starter Tesla1856 AVS Special Member Join Date: Mar 2009 Location: Texas, USA Posts: 1,405 Last edited: May 14, 2010 Tesla, May 13, 2010 #2 Advertisements (*steve*) ¡sǝpodᴉʇuɐ ǝɥʇ ɹɐǝɥd Moderator Joined: Jan 21, 2010 Messages: 20,593 Likes Received: 1,455 Location: Mid way between Beijing and

In most cases, they need to be 8 ohms. My receiver had been working perfectly for about 6 years before error message slowly started to kick in.ReplyDeleteRepliesMartin QJune 11, 2013 at 7:43 AMYes it should. They are not user-replaceable as they are PCB mounted, and thermally coupled to a heatsink. Pulled up Tesla1856 directions, and looked at voltages on pin 12 for both IC601/IC602 with the idea of testing which amp was raising the overload signal.

By now it had been un-plugged for about 30 minutes. Now that could still be the front of the fets, but I'm thinking no since its comes right off the top of the heatsink. Explore Home AV A/V Receivers Blu-ray Disc Speakers 2-Ch Components Turntables Headphones High-Res Audio Bundles Mini Stereo Systems Featured Product: SC-LX901 DJ DJ Pioneer DJ Products are the standard for Professional What caps do you propose changing Martin?

Living Room Home-Theater: Epson 8350 Projector (1080p @ 96") / Panasonic 850u 46" 1080p Plasma TV Onkyo TX-sr607 AVR (7.2ch ~ HDMI ~ wrat-Amp 630 watts ) AppleTV-4 / Panasonic dmp-BD60 Click to expand... With the old (but still pliable) silicone the front of the MOSFETs themselves would get very hot.