panasonic dvd-rp62 error codes Adams Wisconsin

PC Repair, Networking, Electronic Sales, Discount Flat Rat.

PC Repair, And Discount Consumer Electronics.

Address Merrimac, WI 53561
Phone (702) 706-8443
Website Link http://www.mtgenterprises.webs.com
Hours

panasonic dvd-rp62 error codes Adams, Wisconsin

H07 - and Panasonic in Australia just gave me an address of a repairer which I will contact tomorrow. I have a RP91 that is giving a H02 error. Good luck and hopefully I will not need to come here again. Provero anch'io a mettre una goccia d'olio nell'alberino del motore e vedremo se potro riutilizzarlo o BUTTARLO!!!

I could get the DVD player to spin the disc but it was noisy and the tracks look properly lubicated. It was clipped in on the front edge with two small hooks, so a degree of BFI was required. Forum Jump: User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home Articles AVS Forum® Articles Community Articles Contest Terms & Conditions rob sheehan New memberUsername: MrfixeruperLynnwood, Wa Sonomish Post Number: 2Registered: Mar-05 Posted on Wednesday, March 09, 2005 - 06:13 GMTfor all who want to fix h07 error.

Definatley Panasonic is using brushless for their models and back then before they swithced to brush for some unknown reason. What kind of motor will be suitable to replace the transverse one because it also dies from a similar failure to teh spindle which will affect the door and optical. James R. It had to be cycled a few times to get the gears back in place.

The retina receives light first , processes and transforms light energy into irritation - a signal that encodes all the information about what the eye sees . I can defaintely hear the brushless motors because they are high-pitched. Manuals Attwood Manuals Yamaha Manuals Lowrance Electronics Manuals Raymarine Manuals O'Brien Manuals Show All > Top Musical Instrument Device Types Microphone Manuals Musical Instrument Manuals Electronic Keyboard Manuals DJ Equipment System Especially often we hear it buy clomid online in the phrase " retinal detachment ." So what is the retina ?

I watched the action by holding down the small buttons on the right side, fooling the player into thinking the lid was closed. I think I had to call the parts department. I hope there is an explanation for this. Don't buy any Panasonic products because they won't provide you with any support.

Go buy a Philips, Sony, Toshiba, the list goes on and on. Sucks! I blew around the motor with compressed air and manually spinning it around, now it works fine and H07 didn't show up anymore. -Mike- 4 of 15 Jun 2, 2003 So that's great!

No more H03 and no more rattle. Loading...Oops :Please try again. I have a Panasonic DVD/CD player Model number DVD-RP62 which I've had since mid/late 2002. thanks to this forum, I saved $200.00 in repairs.

Do not pull on the wire. Next open the dvd player by removing the 7 screws (2 on each side and 3 on the back on my model). mr. Also if you have your player open and you can see the number on the motor please let me know as well.

Put the cover back on and after tesing one or two discs the thing goes back into HO2 mode. The place near me charges flat $65 for labor. I saw the spindle arm - it's about 60mm long, and to the side of the lens mounting. Add a comment Add a comment Add Comment 1024 Step 4 Edit Note that the spindle you will be lubing is located underneath the white disk device highlighted in figure one

But alas, the H02. David Massey Silver MemberUsername: SamijubalPost Number: 618Registered: Jul-04 Posted on Wednesday, February 16, 2005 - 20:41 GMTWhat's using direct drive? Entries RSS Comments RSS Log in And a few words about the structure of the eye . Going to try fix it myself now using the oil idea (thanks for the tip btw).

Gone in 60 Minutes....two machines. Don't put too much stress on it! Terms of Use For the best viewing experience please update your browser to Google Chrome « Back x Cookie and Data Use Consent We use cookies to improve your experience on Turns out that piece of plastic had found the laser pickup.

The spindle motor is relatively small and expectedly wuld Question about Panasonic DVD & Blu-Ray Players 1 Answer My DVD player says HO7 and then stops ...HO7 and then stops Hi, Definately one of these guys or a differnet one is on these units which have brushless. Hossam's advice just saved me a bundle as well. rob sheehan New memberUsername: MrfixeruperLynnwood, Wa Sonomish Post Number: 1Registered: Mar-05 Posted on Monday, March 07, 2005 - 03:27 GMTi have repaired about 9 of these units ,the problem is with

Disassembled the thing and lubed the spindle motor, everything works great with the cover off. Now it seems I am having the H05 laser tracking error. You can see their brushless motor's here and you can see the data cable in the picture and in teh specs. The motors are so quiet you can't hear them over the sound of the disc spinning.

Disassembled the thing and lubed the spindle motor, everything works great with the cover off. until now i've thinking to replace the damn motor whit a cdrom unit one, but i cannot tried the idea yet. LeoDLion: Have you hooked up your Oppo 980H? AVSForum.com is not sponsored by or in any way affiliated with AV Science Inc.

Shaking doesn't do it for my unit. richieUnregistered guest Posted on Tuesday, January 11, 2005 - 07:49 GMTMy panasonic RV32 dvd player just gave me the death signal "H07" error mesage. Follow our team for updates featuring event coverage, new product unveilings, watch industry news & more! error message...

Browse Categories Answer Questions Panasonic DVD-RV27 DVD Player Panasonic DVD and Blu-Ray Player DVD & Blu-Ray Players All Unanswered Join Sign In Ask a Question × HomeForumDVD & Blu-Ray PlayersPanasonicPanasonic DVD-RV27 I ordered a optical pickup assembly from Partstore.com at $72. How does the image quality compare to the RP91? Anonymous Posted on Wednesday, March 09, 2005 - 21:20 GMTYup but what about the use of another motor which rob mentioned?

d'errore H07. I did not have to remove the metal plate that holds the lazer head or any cables for this repair, but the assembly and the cables do unclip easily. Now lubricate the motor. You may have to remove some pieces to get at the spindle, but once you do, fixing it should be a snap.

Sango David Massey Silver MemberUsername: SamijubalPost Number: 617Registered: Jul-04 Posted on Tuesday, February 15, 2005 - 02:12 GMTI don't know the specs of the motors.